Compare Prices

Methanol Injection System


 - Nitrous Express 15055 Fluid Flow Solenoid Upgrade with Fittings for Water-Methanol Injection System
Nitrous Express 15055 Fluid Flow Solenoid Upgrade with Fittings for Water-Methanol Injection System

The Nitrous Express fluid flow solenoid upgrade for water-methanol injection system is required if the nozzle is to be installed after the intake throttle plate, or the fluid reservoir is mounted higher then the nozzle. It is highly recommended for trunk-mount or rear-mounted reservoirs. Fittings are included.

  • Brand: Nitrous Express
  • ASIN: B00470DN5I
  • UPC: 653374010863
 - Nitrous Express 15050 2.5 gallon Reservoir with Fittings and Brackets for Water-Methanol Injection System
Nitrous Express 15050 2.5 gallon Reservoir with Fittings and Brackets for Water-Methanol Injection System

The Nitrous Express 2.5 gallon (9.3 liter) reservoir with fittings and brackets for water-methanol injection system gives much more range than the included 3 quart tanks and is fairly small in size. It comes in dimensions of 13 inch length, 9.5 inch height and 7.5 inch width. It is hence similar to a very small car battery.

  • Brand: Nitrous Express
  • ASIN: B00470DMZO
  • UPC: 653374010818
 - AEM (30-3312) V2 Water/Methanol Injection Nozzle and Jet Kit
AEM (30-3312) V2 Water/Methanol Injection Nozzle and Jet Kit

AEM's Water/Methanol Nozzle and Jet Kit allows users who require additional water/methanol volume to match their engine's requirements by adding an additional injector. This kit includes one precision-machined billet injector with integral check valve to prevent unintended fluid flow, three billet injector nozzles to match water/methanol flow to an engine's horsepower output, one foot (12 inch) of 1/4 inch nylon injection tubing and a T-fitting to integrate the additional nozzle into an existing system.

  • Brand: AEM
  • ASIN: B00GSIBC3W
  • UPC: 106107228368
 - AEM (30-3300) V2 1-Gallon Water/Methanol Injection Kit with Internal MAP Sensor
AEM (30-3300) V2 1-Gallon Water/Methanol Injection Kit with Internal MAP Sensor

Water/Methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of up to 20 percent. AEM's Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system. The on-demand progressive controller in AEM's Boost Dependent Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine's power curve.

  • Color: Black
  • Brand: AEM
  • ASIN: B00GSBKNF2
  • UPC: 840879022600
 - AEM (30-3320) V2 Water/Methanol Injection Tank Kit - 5 Gallon Capacity
AEM (30-3320) V2 Water/Methanol Injection Tank Kit - 5 Gallon Capacity

The AEM Water/Methanol 5 Gallon Tank can be used with nearly any water methanol kit using 1/4 inch OD hose for extended range or as an upgrade to competitor systems that supply tanks less than 5 gallons. The tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness. Comprehensive hardware for mounting is included. Dimensions: 21 inch long x 8 inch wide x 10 inch tall with cap installed (9 inch tall without cap). All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100 percent chemically compatible with methanol. However, for safety reasons it is strongly recommend that users never use more than a 50 percent methanol concentration in systems.

  • Brand: AEM
  • ASIN: B00GSIBBNS
  • UPC: 840879022716
 - AEM 30-3015 Water/Methanol Injection Pump
AEM 30-3015 Water/Methanol Injection Pump

AEM's recirculation style pump offers improved performance, reliability and a much smoother, quieter operation when compared to older switched style pumps. With the use of a new internal bypass design, AEM's upgraded pump eliminates the erratic on and off switching/pulsing and ensures consistent fluid delivery for optimum performance. With durability and reliability in mind, AEM has designed the pump with a Santoprene diaphragm and EPDM seals to withstand the harshest of alcohol mixes.

  • Color: black
  • Brand: AEM
  • ASIN: B005ASY2ME
  • UPC: 840879021412
 - Stage 2 Boost Cooler Forced Induction Progressive Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)
Stage 2 Boost Cooler Forced Induction Progressive Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)

Innovative engineering, extensive field testing. Exceptional quality control. Provides longer brake life and performance. Easy installation, direct fit, perfect replacement. Offering the quality, reliability, and durability

  • Brand: Snow Performance
  • ASIN: B079HBZ7T8
  • UPC: 608067063121
 - Nitrous Express 15056 Nozzle Mounting Adapter for Hose in Water-Methanol Injection System
Nitrous Express 15056 Nozzle Mounting Adapter for Hose in Water-Methanol Injection System

The Nitrous Express nozzle mounting adapter for hose in water-methanol injection system allows you to mount your injector nozzle into your silicone or rubber intake tube. The adapter is methanol resistant and highly durable. The installation is easy and includes simply drilling a 3/4 inch hole using a spade bit, inserting the inner adapter piece, and thread on the outer adapter nut.

  • Brand: Nitrous Express
  • ASIN: B00470EXGG
  • UPC: 653374010870
 - Nitrous Express 15020 Water-Methanol Injection System for Gas Stage 1 Boost Engine
Nitrous Express 15020 Water-Methanol Injection System for Gas Stage 1 Boost Engine

The Nitrous Express water-methanol injection system for gasoline, stage 1 engines is very versatile. It can be used in naturally aspirated or forced induction applications. The system includes an adjustable boost activated switch for forced induction applications as well as a wide open throttle switch for naturally aspirated applications. The operation is very simple where the system starts injecting when the boost or wide open throttle switch is activated and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low to medium horsepower setups looking for an octane enhancement and cooler intake charge. The system includes a UHO (Ultra High Output) pump, a 3 quart reservoir, 2 nozzles to cover a wide range of horsepower, WOT (wide open throttle) switch, boost activated switch, required hardware needed for installation and comprehensive instructions.

  • Brand: Nitrous Express
  • ASIN: B00470BHG0
  • UPC: 653374010962
 - Stage 1 Boost CoolerTM Forced Induction Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)
Stage 1 Boost CoolerTM Forced Induction Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)

Innovative engineering, extensive field testing. Exceptional quality control. Provides longer brake life and performance. Easy installation, direct fit, perfect replacement. Offering the quality, reliability, and durability

  • Brand: Snow Performance
  • ASIN: B079HV3297
  • UPC: 608067063084
 - AEM (30-3306) V2 Water/Methanol Injection HD Controller Kit with Internal MAP Sensor
AEM (30-3306) V2 Water/Methanol Injection HD Controller Kit with Internal MAP Sensor

AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded-in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs. AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels. AEM's Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the syste...

  • Brand: AEM
  • ASIN: B00GSIBDJK
  • UPC: 840879022709
 - AEM 30-3350 AEM30-3350
AEM 30-3350 AEM30-3350

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows enthusiasts to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of up to 20percent. AEM's Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system. The on-demand progressive Multi-Input controller in AEM's PN 30-3350 Water/Methanol Injection kit for gasoline vehicles features a multiple input design that enables users to install AEM's Water/Methanol Injection Kit on both high compression naturally aspirated vehicles (NA) via the MAF/IDC settings and ultra-high boost vehicles (above 35 PSI) using an external MAP sensor. The Multi-Input controller works with an external 0-5v voltage-based external MAP sensor, a frequency based input for Injector Duty Cycle (IDC), frequency-based mass airflow (MAF), or a 0-5v voltage-based MAF. The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and te...

  • Brand: AEM
  • ASIN: B00GSBRUP8
  • UPC: 840879022617
 - AEM 30-3304 AEM30-3304
AEM 30-3304 AEM30-3304

AEM's Boost Dependent water/methanol injection controller is ideal for vehicles running up to 35 PSI of boost. It has an on-board manifold absolute pressure (MAP) sensor with a molded-in, barbed nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs. AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and detonation control on gasoline engines or EGT reduction on turbo Diesels. AEM's Water/Methanol Injection wiring harness for the Boost Dependent 35 PSI controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness whi...

  • Color: black
  • Brand: AEM
  • ASIN: B00GSIB57K
  • UPC: 840879022686
 - SNOW PERFORMANCE (4 PACK) BOOST JUICE 1 GALLON EACH - Water Injection System Fluid / PCK#4X40008#4 /
SNOW PERFORMANCE (4 PACK) BOOST JUICE 1 GALLON EACH - Water Injection System Fluid / PCK#4X40008#4 /

Pack of 4 X BOOST JUICE 1 GALLON EACH BOOST JUICE 1 GALLON EACH Boost JuiceTM is Snow Performance's proprietary mix of 49 Percentage methanol and 51 Percentage water. It is made in a controlled environment with special care to make sure the ratios are accurate to result in a high performance water methanol fluid formulated for use in the Boost CoolerTM injection system. Boost Juice is required as the exclusive fluid for lifetime warranty Use With: Boost Cooler Injection System Color: Red

  • Brand: Snow Performance
  • ASIN: B01M3UDL31
  • UPC: 670579249294
 - AEM (30-3305) V2 Multi-Input Water/Methanol Injection Standard Controller Kit
AEM (30-3305) V2 Multi-Input Water/Methanol Injection Standard Controller Kit

AEM's Multi-Input water/methanol injection controller features a multiple input design that enables users to install it on both high compression naturally aspirated vehicles (NA) via the MAF/IDC settings and ultra-high boost vehicles (above 35 PSI) using an external MAP sensor. The Multi-Input controller works with an external 0-5 volt voltage-based external MAP sensor, a frequency based input for Injector Duty Cycle (IDC), frequency-based mass airflow (MAF), or a 0-5 voltage-based MAF. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Multi-Input controller has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5 volt and frequency based settings. The controller housing features an easy to access integrated fuse and molded mounting tabs. AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol in...

  • Brand: AEM
  • ASIN: B00GSIBC4G
  • UPC: 840879022693
 - Nitrous Express 15025 Water-Methanol Injection System for Gas Stage 1 Naturally Aspirated Carbureted Engine
Nitrous Express 15025 Water-Methanol Injection System for Gas Stage 1 Naturally Aspirated Carbureted Engine

The Nitrous Express water-methanol injection system for gasoline stage 1, naturally aspirated and carburetor run engine increases your pump gas octane by 20-25 points and makes more power. It works on engines with 11:1 to 13:1 compression ratio or more. This gives more power and efficiency with cooler running for your naturally aspirated V8 muscle car. This system uses a wide open throttle switch to activate the water/methanol only under full load. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. This system allows you to save money by using lower grades of gasoline. It comes with one 4150-style carburetor spacer plate threaded for 1/8 inch injection nozzles, and a solenoid to prevent vacuum siphoning. The system includes SHO (Special High Output) pump, 1 inch carburetor spacer plate, solenoid valve to prevent siphoning, 3 quart reservoir, WOT (Wide Open Throttle) switch, 2 nozzles cover a wide range of horsepower, all required hardware needed for installation and comprehensive instructions.

  • Brand: Nitrous Express
  • ASIN: B00470DMOA
  • UPC: 653374010726
 - AEM 30-3003 Water/Methanol Injection Filter
AEM 30-3003 Water/Methanol Injection Filter

The AEM Water/Methanol Injection Filter is an in-line filter that uses a micronic mesh screen to filter particulates as small as 40 microns. This allows a cleaner flow of water/methanol to be passed into the engine, not only protecting the internals of the engine itself, but also the working parts of the water/methanol pump too. Run the AEM Water/Methanol Injection Filter in-line before the pump to protect both pump and engine. If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4inches OD nylon tubing, so it fits most Water/Methanol injection kits on the market today.

  • Brand: AEM
  • ASIN: B0032W3KH8
  • UPC: 840879020941
 - Nitrous Express 15054 Carb Plate for Water-Methanol Injection System
Nitrous Express 15054 Carb Plate for Water-Methanol Injection System

The Nitrous Express carb plate for water-methanol injection system

  • Brand: Nitrous Express
  • ASIN: B004LFCHE2
  • UPC: 653374010856

Methanol Injection System M836 Search Results

Looking for more Methanol Injection System similar ideas? Try to explore these popular searches: Cd Electric Flag, Plus Free Drill Driver, and Hot Pink High Heel.

Look at Methanol Injection System Video Reviews

Watch this before running Methanol Injection

Methanol Injection System Review

Watch this before running Methanol Injection In this video, I discuss the pros/cons and some mis...

Tags: meth,methanol,methanol injection,cooling,cleani...

Which Water-Methanol Injection Kit is Right For You?

Methanol Injection System Review

Join us as we go through our various stages of water-methanol injection systems to find which kit...

Tags: methanol,methanol injection,water injection,wat...

Methanol Injection- What is it? Why you need it? How does it work?

Methanol Injection System Review

Watch this video on Methanol Injection. This video will explain what it is and why performance en...

Tags: Methanol (Chemical Compound),meth injection,efi...

Is Meth Injection Worth it? | The Build Sheet

Methanol Injection System Review

So we have talked about nitrous, but now it's time to dive in to meth injection. Today Gels goes ...

Tags: Fitment Ind,Custom Offsets,Offsets Garage,Apple...

DID IT WORK? Snow Performance Methanol Injection Kit!!!

Methanol Injection System Review

Showing the Scan results from before and after the methanol injection kit. Have Kids? Check Out...

Tags: a21 bravo,a21bravo,lq4,lm7,l33,lq9,budget ls sw...

Xldealo.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com