Kenwood DMX7705S 6.95â€ Media Receiver, Apple CarPlay and Android Auto, iDatalink KIT-F150 Dashkit for Select Ford F-150, ADS-MRR Interface Module and BAA21 Antenna Adapter and a SOTS Lanyard
Kenwood DMX7705S 6.95" WVGA Media Receiver, Bluetooth, Apple CarPlay and Android Auto Ready (does not play CDs)6.95" WVGA Media Receiver, Bluetooth, Car Play Ready and Android Auto Ready, USB Weblink for iPhone/Android phone supporting Waze, Yelp, You Tube and Weather, Dual Rear USB's, SiriusXM Ready, iDatalink Maestro Ready, Front/Rear Camera InputsiDatalink K150 Dash KitInstall a new car stereo in select 2013-14 Ford F-150 models with 4.3" "My Ford" screenallows you to install an aftermarket double-DIN radio in your F-150ADS-MRR module is required to complete installation and retain steering wheel controls (included)kit matches color, texture, and contours of dashpocket included with HDMI, auxiliary, and USB inputs that connect to your new radioretains factory amplifier and backup cameraretains SYNC features with any iDatalink-compatible car stereodisplays engine performance data on touchscreen with select Alpine, JVC, Kenwood and Pioneer receiversiDatalink Maestro ADS-MRR Interface ModuleConnect a new stereo and retain the steering wheel audio controls and factory amps in select 2006-up vehiclesworks with required vehicle-specific harness to retain factory steering wheel audio controls, retain the factory amp if present, and integrate all car stereo connectionsnot compatible w...
- Brand: Kenwood
- ASIN: B07H418XWV
- UPC: 661585121889
OctagonStar USB to TTL/RS485 Serial Converter Adapter FTDI Interface Board FT232RL Module
Size: 3.07in x 0.75in x 0.79in.Package include: 1 x USB To TTL/RS485 Module .
- Brand: OctagonStar
- ASIN: B01LCFRR3E
- UPC: 709586709542
DMX Shield MAX485 Chipset for Arduino (RDM Capable)@CQRobot, Arduino Device into DMX512 Network. LED/Music Remote Device Management Capable, Extended DMX Master and Slave Arduino Device Functions.
INTRODUCTION The Arduino DMX shield is an add-on (or "shield") for the Arduino. It is an easy way to use the Arduino as a DMX-Master device, just by adding the DMX-shield on the top of the Arduino. This DMX / RDM Shield is a low cost high quality solution that allows you to connect your Arduino driven artwork into DMX512 networks. The shield is populated with high quality NEUTRIK XLR 3pin Connectors (1x male and 1x female). The MAX485 based shield can be used as DMX Master, Slave and as RDM transponder.A unique RDM device id will be handed out from out range to you as well, this will make your device worldwide unique. The following settings are configurable via the onboard jumpers: - Send data via TX or Digital pin 4 - Receive data via RX or Digital pin 3 - Hardware slave mode or Software Controlled Slave/Master via Digital pin 2 (Required for RDM) - Enable / Disable shield In case you have the shield configured to use the RX and TX pins you have to disable the shield before you can upload your new sketch onto the Arduino board. This jumper allows you to disable the shield without disconnecting it from the Arduino board which saves time. WIKI http://www.cqrobot.wiki/index.php/DMX_Shield_for_Arduino-CQR0260 SPECIFICATION Remote Device Management DMX Master DMX Slave SHIPPING LIST...
- Color: Arduino-DMX Shield
- Brand: CQRobot
- ASIN: B01DUHZAT0
- UPC: 712104520895
USB to Ttl/rs485 Ftdi Interface Board Ft232rl 75176 Module
Standard: USB2.0 standard, backward compatible, in line with the standard RS485. Direction control: the use of automatic data flow control, auto distinguish and control data transfer direction. Baud :300-9216000bps, automatically detecting the serial signal data rate. Load capacity: support multipoint, each converter allows RS485 interface device to connect 32. Interface Protection: TVS tube protection, USB self-recovery protection. Support Windows98/ME/2000/XP/WIN7/Vista, Linux, Mac. Support devices with RS485 interface: surveillance cameras, video capture device, fingerprint attendance machine, PBX, CNC machine, microcontroller, etc. This converter provides two way serial communications signal. Conversion between the RS485. To and from a personal computer USB port. Using virtual serial COM port. Self-powered from USB. Size:7.8cm x 1.9cm X 2cm - 3.07inch x 0.75inch x 0.79inch. It can be up to 32 devices on the bus Package include: 1 x USB To RS485 Module
- Brand: Generic
- ASIN: B00O6Q2PKM
- UPC: 697313334771
LED DMX512 Computer PC Stage Lighting Controller Dimmer USB to DMX Interface Adapter with CD
Feature : 1. Supports Freestytle software. DMX512 times,configurable. 2. USB A male metal shell to Din 3pin female adapter cable. USB DMX Interface. Micro processor enabled. 3. Support for Windows XP, Vista, Windows 7, Windows 8, Windows 10 ( 32bit and 64bit ). The CD includes drivers, Freestytle software Item Describe: 1. 100% Brand New and High Quality 2. Type : USB to DMX Adapter 3. Material: Plastic 4. Size: 14.5 x 10.8 x 4.7cm 5. Cable length: 110cm Package includes: 1 x USB to DMX Interface Adapter 1 x CD 1 x Use Manual
- Brand: ElectronicNova
- ASIN: B07V25KJV9
MonkeyJack Stage Light Controller, USB to DMX Interface Adapter, Dimmer, DMX512
Description: - USB A male metal shell to Din 3pin female adapter cable - USB DMX Interface. - Micro processor enabled. - Supports FreeStyler software. - DMX512 times configurable. - Support for Windows XP, Vista, Windows 7, Windows 8, Windows 10 ( 32bit and 64bit ) - The CD includes drivers, FreeStyler software, installation video.Specification: - Main color: Back - Material: ABS Plastic - Caple length: 106cm/3.477ft - Black part: 6*11cm/2.36*4.33''Package Includes:1 Piece USB to DMX Interface Adapter1 Piece CD1 Piece User ManualNote:Please follow the instruction to install the driver and software carefully.Due to the light and screen setting difference, the item's color may be slightly different from the pictures.Please allow slight dimension difference due to different manual measurement.
- Brand: MonkeyJack
- ASIN: B07931KS9K
- UPC: 753321127290
Pukido TDA7492P 225W Bluetoo 4.0 Audio Receiver Amplifier Board Module with AUX Interface + Acrylic DIY Case Kit Cover
TDA7492P 2*25W Bluetoo 4.0 Audio Receiver Amplifier Board Module with AUX Interface + Acrylic DIY Case Kit Cover Sound quality is very good and it can drive 4/6/8/16 ohm speakers. Bluetooth V4.0, it has sufficient power output 2*25W. The DIY case is greatly designed for protect he module efficiently.Features:Audio Receiver Board:Sound quality is very good by using this module.Equipped with AUX interface. Using CSR8635 Bluetooth chip, Bluetooth V4.0, high software compatibility.After power on, automatically enter into pairing mode, search the name: SANWU Audio.With 5 buttons for adjustment, convenient and easy operation.Applicable speaker impedance: 4/6/8/16 ohm (8 ohm is the best).Case:DIY case for TDA7492P 2*25W Bluetooth 4.0 audio receiver board.Acrylic material, looks transparent(need to tear down the film).High quality case, protect the module efficiently.Easy for electronic enthusiasts to assemble.Specifications:Audio Receiver Board:Supply Voltage: DC 8-25VPower Interface: 2.1 DC SocketAudio Input: Bluetooth Receiver V4.0Audio Output: TerminalsOutput Power: Add Pre-5532 Output FootApplicable Speaker Impedance: 4/6/8/16 ohmNumber of Channels: Two-channel Stereo PCB Board Size: 82 * 50mm / 3.23 * 1.97inWeight: 37g / 1.32ozCase:Material: AcrylicCase Size: Approx. 91 * 60 * 2...
- Brand: Pukido
- ASIN: B07KX4NJ3S
- UPC: 765251609524
Muccus New Lilypad Pixel Board WS2812 Module for
Warm prompt: Dear buyer, Our cheapest transportation services Economic category logistics (SunYou Economic Air Mail ,China Post Ordinary Small Packet Plus ) can be traced only befor it arrive your country,please choose Standard category logistics if you want a full tracking info. Descriptions:We know you love adding color to your e-textiles, adding the LilyPad Pixel Board to your project will only make it better. The pixel board is equipped with a WS2812 which is actually an RGB LED with a WS2811 built right into the LED! Several of these breakouts can be chained together to form a display or an addressable string. LilyPad is a wearable technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!Item specifics:Type: Voltage RegulatorCondition: NewApplication: ComputerSupply voltage: 1Dissipation power: 1Is customized: Yes
- Color: 14m i2c board button buzzer lilypad 552 rgb ring power interface dmx strip
- Brand: Muccus
- ASIN: B07L5T1196
- UPC: 765251791236
CHINLY 12 channel DMX 512 RGB LED strip controller dmx decoder dimmer driver DC5V-24V 5A/CH (12CH DMX 512 Decoder)
12CH-DMX512 Constant decoder Operation Instruction Welcome to use the 12CH constant decoder, which take advantage of advanced microelectronic control technology. This technology changes the international fashion DMX512/1990 standard digital control signals into analog control signals. There are 1 ~ 12 output channels; each channel can achieve 256 control levels. This constant decoder is used when DMX512 control equipment control general LED lighting Products Performance: Input Power: DC5V-DC24V Maximum load current: 5A/CH×4 Maximum power load: 300W(5V) 720W(12V) 1440W(24V) Output gray level: 256 Input Signal: DMX512/1990 Output signal: 12 channels Constant PWM Output DMX : 12 channels DMX512 socket standard RJ45 Engine size: L6.1in*W3.5in*H1.2in Gross Weight:0.73lb Basic functions: There are 12 output channels, can connect with single or RGBW lamps 0-100% dimming output, each channel 256 gray levels International standard DMX512 input protocol, address code set by DIP switches; Wide voltage DC input DC5V ~ DC24V; Each occupied by 12 DMX address. Package Included: 1 x DMX 512 Decoder 1 x DMX cable 1 x User Manual
- Color: 12 Channel
- Brand: CHINLY
- ASIN: B01MSGZMOR
- UPC: 744960166184
BTF-LIGHTING Digital Addressable Led Strip Music Controller X2(X1 Updated Version) for WS2811 WS2812B 6803 WS2813 WS2815 LED Strip DC5V-24V
copy this link to the browser https://youtu.be/Q24vOk9DQ18 you will know how to use it . Technical Parameters: 1.Remote Distance :>20meters 2.Operating Temp.:-20℃- 55℃ 3.Gross.W.: 350g 4.Package box:L188*W140*H39mm 5.Remote Control Freq.: 433MHz RF 6.Power Supply:2*AAA battery ( Products do not contain batteries) 7.TX Power: 6db 8.Standby Power Consumption:10uA 9.Receiver input:DC5V-DC24V(the same as the led strip) the receiver input voltage must be the same as the LED Strip 10.Output :Digital Signal ,Max 1000ICs 11.Operating Noise Level:
- Color: White
- Brand: BTF-LIGHTING
- ASIN: B0759PQ46B
3 Channels DMX-521 Decoder LED Controller For RGB Strip Light
Each DMX common controller occupied 3 DMX address, adopt coding switch is setting DMX original address code from 1 to 9, 1 is the lowest, and 9 is the highest , 511 address code could be setted in all. This DMX common controller adopts the advanced micro control unit, receives standard DMX-512 digital control signal and transformed it into PWM signal to driving LEDWith over 30 preprogrammed color changing patterns, including gradual changing, screening and jumping, our DMX controller offers a variety of display options.. As a powerful color managing controller, it will enable you to choose the desired pattern and appropriate speed to manage your RGB LED lighting fixtures.With 0 to 100 dimming grades, you can also control the color and brightness according to your requirements easily, and mix up to 1 million different colors.The mounting bracket will enable the operator to easily fix the controller onto any place.Each DMX common controller occupied 3 DMX address, adopt coding switch set address. The max output power is 144 watts, enable you to connect 20M RGB strips of 150LEDs or 10M RGB strips of 300LEDs.Specifications:-Working temperature: -20 to +60 centigrade -Output: 3 CMOS drain-open output -Connecting mode: common anode -Product size: L166*W67*H41mm -Net weight: 340gAppli...
- Color: Silver
- Brand: TORCHSTAR
- ASIN: B0083RBGJG
- UPC: 741459500733
JOYLIT Wall-Mounted Acrylic 4Channels Touch Panel Controller for RGBW LED Strip Lights DC12V-24V
RGBW touching Controller is new generated product. The controller is adopted glass panel and ABS plastic to base. Professional PCB design to avoid circuit problem. Luxury Design,Fashion appearance. The controller can be installed embedly to wall. Can be connected to all led lights in DC5,DC12-24V. Example: led module, dot matrix light,flexible strip, wall washer ect. Install convenience and operate easily. Can be allocated to hotel decoration, home decoration, commercial lighting area and leisure place ect. >>>Technical Specification: 1. 4CH output, 4A/CH, 16A / 4 Channels 2. Input voltage:DC5V, DC12-24V 3. Max Power: 80W @ 5V; 192W @ 12V; 384W @ 24V 4. Connecting mode: common anode 5. Static Power consumption: >>Package Including: 1 x RGBW Led Touch Controller
- Color: T-RGBW
- Brand: JOLLTY
- ASIN: B07FCJW1V8
- UPC: 723740606256
Alexa Lighting Inteface - connect Alexa to standard LED drivers. DMX, DALI, 0-10v, AL-DALI-WIZ
Communicates with the Alexa Cloud. 3 standard Lighting interfaces in one device DALI interface DMX interface 0-10v interface Multi Master technology allows multiple modules to control one DMX universe Combine with AL-DMX-WS to mix physical switches with virtual control 4 popular DMX configurations 512 address universe DALI control set Address, Group, Scene, Broadcast requires a 24v power supply - power supply included
- Color: multi
- Brand: ATX LED
- ASIN: B07F611QNW
- UPC: 784099948473
Antari Z-1500 II Fog Machine
Its energy-efficient 1500W heater outputs 20,000 cubic feet of dense swirling fog per minute. DMX controllable it comes with a remote and will stand up to hard touring work. The Elation/Antaris Z-1500II is the result of rigorous research and development to enhance its machine lifetime, stability and reliability. Because of its compact size and durable appearance, the Z-1500II fogger provides significant advantages in wider applications where great volumes of fog output is critical. The Z-1500II saves up to 25% of the electricity of its predecessor. This efficient power control system allowing the fogger to operate at low-level temperatures. These cutting-edge features including a heater pipe made of nickel-aluminum alloy adopted for fast and efficient heat transfer. The heater element is enormously powerful and robust which generates great volumes of fog output in a steady and silent extrusion without leaving any residue inside. An electronic low fluid detector with Thermal Cut-Off (TCO) is also installed which automatically cuts off the pump power and stop pumping when running-out of fluid. Z-1500II has a built-in dual DMX-512 interface and can be controlled remotely with a digital display control module.
- Brand: Antari
- ASIN: B002Q9N7R6
- UPC: 837874009316
LEDJump Musical Professional Selection DMX512 4A 3 Channels Decoder Controller Dimmer for RGB LED Light Strip DC12V-24V DMX 512
Description: DMX-512 Common Controller Dimmer for RGB LED Light Lamp, can support 30cm to 20M(30 led bulb/M) RGB LED strip. This DMX common controller adopts the advaned micro control unit, it receives standard DMX-512 digital control singal and transformed it into PWM signal for driving LED; You could connect DMX module with DMX digital console to achieve dimming or various changes in procedures. Specification: Working temperature: -20- 60 Deg Supply voltage: DC12V-24V Output: 3 Channels Connection mode: Common Anode Product size: L164 x W65 x H40mm Package Size: L175 x W83 x H48mm Output current: each channel 4A Output power: 12V, 144W, 24V:288W Features: How to use? 1. DMX address code settings: Each DMX common controller occupied 3 DMX addresses, adopt coding switch set address, it is a Binary numerical code switch which is setting DMX original address code from 1 to 9, 1 is the lowest, and 9 is the highest, 511 address codes could be fixed in all. DMX original address code equal aggregate value of the coding switch value from 1 to 9, dial the coding switch upwards (ON is setted 1), the value of bit can be gotten, on the contrary, the value of bit is 0. DMX signal can be received when coding switch FUN(10)-OFF 2. Other functions direction for use: 1) Tes...
- Brand: LEDJUMP
- ASIN: B00KQ3NY5E
DCD5V~DC24V 360W 24-channel DMX512 constant voltage decoder PWM stage lamp engineering 24-channel controller decoder, RGB controller
Goods No.: DMX512-24CH ??:JM-DMX512-24C Control: DMX512 & nbsp; weight: 920G Control Range: RGB Lamp, Monochrome Lamp, Lamp, Module, etc.. Rated voltage: 5-24 Connection mode: terminal Interface Type: Terminal Protection Level: IP20 Shape size: 249 * 105 * 43 Signal mode: DMX to PWM Contains: 1* decoder (with a pair of Cannon plugs)
- Brand: Trihedral
- ASIN: B07T35LTWQ
QWinOut New 3DR Wireless Data Transmission Radio 433M 500mW RX+TX Telemetry w/OTG for APM2.6 2.8 Pixhawk FPV System Antenna
Descriptions: - The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. It\'s availabl in 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground). - The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface, based on HopeRF\'s HM-TRP data link modules, and custom firmware that improves upon the modules\' original features and performance. - The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through AT commands. 3DR Telemetry Kit Specifications - 433MHz and 915MHz for opotional. - Very small size - Light weight (under 4 grams without antenna) - 433-434.79MHz - Receiver sensitivity to -118 dBm - Transmit power up to 20dBm (500mW) - Transparent serial link - Air data rates up to 250kbps - MAVLink protocol framing and status reporting - Frequency hopping spread spectrum (FHSS) - Adaptive time division multiplexing (TDM) - Support for LBT and AFA - Configurable duty cycle - Built in ...
- Brand: QWinOut
- ASIN: B01MRZCRFQ
- UPC: 612677826151
Look at Dmx Interface Module Video Reviews
Architectural DMX Interface Stick DE3 Made by Sunlite Review
http://sirs-e.com/ | http://sirs-e.com/shop/dmx-control/stick-de3/ SIRS Electronics, Inc. | USA P...
Cheap DMX Interfaces [CYL-6602 USB-DMX]
Buy here: http://www.ebay.com/itm/New-1024-Channel-Usb-Dmx512-Cyl-6602-Lighting-Controller-For-Le...
W-DMX™ - First Setup!
Trying W-DMX™ for the first time? Check how easy it is to use. For more visit: www.wirelessdmx.c...
DMX Splitters: Overview
Arduino DMX512 Controller
Using the DMXSimple Arduino library, I was able to get these two American DJ Micro Wash RGBW PAR ...
Xldealo.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com